Flasher Portable PLUS
[5.16.02]

598€ ex. VAT

[IN STOCK]
Handheld  Flash Programmer with Display and internal battery
Flash Programmer  running on batteries with 1.8" Display
Flasher Portable PLUS
Reviews
  • Stand-alone in-circuit-programmer (Once set up, Flasher can be controlled without the use of a PC program)

 
  • internal battery rechargeable Li-Ion 680mA
  • Full insights with 1,8 inch display
  • Up to 10 hours programming 
  • up to eight configurations/data files being stored on Flasher
  • Push button for selection between multiple images/configurations 
  • 128 MB internal memory 
  • Supports ARM, Cortex, PowerPC and Renesas RX cores.
  • Supports internal and external flash devices
  • Free updates
  • Data files can be updated via mass storage or via J-Flash
  • Target interface: JTAG / SWD / FINE / SPD
  • Programming speed between 30 KB/second and 1 MByte/second. depends on target hardware
  • SECURITY: Flasher Portable and Flasher Portable PLUS support Authorized Flashing.
Flasher Portable PLUS—Handheld Programmer with Display .The handheld stand-alone Flash Programmer for on-chip and external flash memory. Flasher Portable PLUS is a battery driven programming tool for microcontrollers with on-chip and/or external flash memory. It has been designed to fill the need of an extremely portable, production grade flash programmer used for in-field firmware updates.

Specifications

Power SupplyVia internal lithium-ion rechargeable battery (Sony US14500VR) or USB
USB Host InterfaceUSB 2.0
Target InterfaceStandard 20-pin J-Link target connector (optional adapters available)
Serial Transfer Rate between Flasher Portable and TargetUp to 15MHz
Supported Target Voltage1.8V - 5V
Current drawn from target voltage sense pin (VTRef)< 25µA
Target supply voltage4.5V max. (depends on current battery voltage)
Target supply currentMax. 400mA
Operating Temperature+ 5 °C ... + 60 °C
Storage Temperature- 20 °C ... + 65 °C
Relative Humidity (non-condensing)< 90% rH
Size (without cables)126mm x 70mm x 28mm
Weight (without cables)140g
Supported OSMicrosoft Windows 2000
Microsoft Windows XP
Microsoft Windows XP x64
Microsoft Windows 2003
Microsoft Windows 2003 x64
Microsoft Windows Vista
Microsoft Windows Vista x64
Microsoft Windows 7
Microsoft Windows 7 x64
Microsoft Windows 8
Microsoft Windows 8 x64
Microsoft Windows 10
Microsoft Windows 10 x64

Target Connection



Since Flasher Portable is compatible to J-Link it also supports the same target interfaces.
Currently the following target interfaces are supported:

  • JTAG
  • SWD
  • FINE
  • SPD

For more information about the target interfaces please refer to J-Link - Interface description.

Standard 20-pin connector pinout

 

 

Flasher Portable uses the standard J-Link 20-pin connector. There are various adapters available to fit all customer needs.

JTAG interface connector signals:

PinSignalTypeDescription
1VTrefInputThis is the target reference voltage. It is used to check if the target has power, to create the logic-level reference for the input comparators and to control the output logic levels to the target. It is normally fed from Vdd of the target board and must not have a series resistor.
2VsupplyNCThis pin is not connected in Flasher Portable. It is reserved for compatibility with other equipment. Connect to Vdd or leave open in target system.
3nTRSTOutputJTAG Reset (optional). Output from Flasher Portable to the Reset signal of the target JTAG port. Typically connected to nTRST of the target CPU. This pin is normally pulled HIGH on the target to avoid unintentional resets when there is no connection. Not mandatory for Flasher operation. Should not be shortened with RESET. In case of doubt, leave open/unconnected.
5TDIOutputJTAG data input of target CPU.
It is recommended that this pin is pulled to a defined state on the target board.
Typically connected to TDI on target CPU.
7TMSOutputJTAG mode set input of target CPU.
This pin should be pulled up on the target.
Typically connected to TMS on target CPU.
9TCKOutputJTAG clock signal to target CPU.
It is recommended that this pin is pulled to a defined state on the target board.
Typically connected to TCK on target CPU.
11RTCKInputReturn test clock signal from the target.
Some targets must synchronize the JTAG inputs to internal clocks. To assist in meeting this requirement, you can use a returned, and retimed, TCK to dynamically control the TCK rate. Flasher Portable supports adaptive clocking, which waits for TCK changes to be echoed correctly before making further changes. Connect to RTCK if available, otherwise to GND.
13TDOInputJTAG data output from target CPU.
Typically connected to TDO on target CPU.
15RESETI/OTarget CPU reset signal. Typically connected to the RESET pin of the target CPU, which is typically called "nRST", "nRESET" or "RESET".
17DBGRQNCThis pin is not connected in Flasher Portable.
It is reserved for compatibility with other equipment to be used as a debug request signal to the target system.
Typically connected to DBGRQ if available, otherwise left open.
195V-Target supplyOutputThis pin can be used to supply power to the target hardware. Supply voltage is 5V, max. current is 300mA. If not needed, leave open.

Notes:
All pins marked NC are not connected inside Flasher Portable. Any signal can be applied here; Flasher Portable will simply ignore such a signal.
Pins 4, 6, 8, 10, 12, 14, 16, 18, 20 are GND pins connected to GND in Flasher Portable. They should also be connected to GND in the target system.
Power can be controlled via the J-Link commander. The following commands are available to control power:
CommandExplanation
power onSwitch target power on
power offSwitch target power off
power on permSet target power supply default to "on"
power off permSet target power supply default to "off"
 

 Flasher User manual
  • Flasher Portable PLUS
  • 20 Pin 0.1" Ribbon Cable
  • USB Cable
  • USB Power Supply
Manufacturers
Quick Find
 
Use keywords to find the product you are looking for.
Advanced Search
ScanaQuad 200
ScanaQuad 200
149€ ex. VAT
Languages
Français
Please Contact Us at: +33 1 3O 50 O9 36
Manufacturer Info
Segger
Segger Homepage
Other products
Payment informations
UPS3D Secure Payment
VISAMasterCard

3D Secure Payment

Mini PC and Car PC

Mini PC and Car PC
Display,
Industrial Control
Transportation