Flasher Portable
[5.16.01]

598€ HT

[EN STOCK]
Programmeur de Flash Autonome fonctionnant sur piles
Programmation des cartes en production, sans necessiter de PC, ni d'alimentation
Flasher Portable
Avis des clients

 
Programmeur de flash autonome (une fois chargé, le Flasher peut etre actionné sans utiliser de PC) fonctionnant sur piles.


-Support ARM, Cortex, Renesas et PowerPC
-Interfaces USB
-Mémoire 128 Mo
-Alimenté par 3 piles AAA
-interfaces JTAG / SWD / FINE / SPD
-Vitesse de programmation 30-1000Ko/s selon cible
-Contrôle du nombre maxi de programmations
-Garantie 1 an
Le Flasher portable  est un outil de programmation pour les microcontroleurs avec mémoire  flash embarquée ou externe. Le Flasher portable est concu pour programmer les mémoires flash des cibles par PC avec le logiciel J-Flash ou en autonome. Il fonctionne sans alimentation grâce à des piles. Il embarque plusieurs configuration / images stockées en interne et selectionnables par un simple bouton.
 

Specifications

Power SupplyCan be powered via battery (3x AAA) or USB
USB Host InterfaceUSB 2.0
Target InterfaceStandard 20-pin J-Link target connector (optional adapters available)
Serial Transfer Rate between Flasher Portable and TargetUp to 15MHz
Supported Target Voltage1.8V - 5V
Current drawn from target voltage sense pin (VTRef)< 25µA
Target supply voltage4.5V max. (depends on current battery voltage)
Target supply currentMax. 400mA
Operating Temperature+ 5 °C ... + 60 °C
Storage Temperature- 20 °C ... + 65 °C
Relative Humidity (non-condensing)< 90% rH
Size (without cables)130mm x 65mm x 25mm
Weight (without cables)120g
Supported OSMicrosoft Windows 2000
Microsoft Windows XP
Microsoft Windows XP x64
Microsoft Windows 2003
Microsoft Windows 2003 x64
Microsoft Windows Vista
Microsoft Windows Vista x64
Microsoft Windows 7
Microsoft Windows 7 x64
Microsoft Windows 8
Microsoft Windows 8 x64
Microsoft Windows 10
Microsoft Windows 10 x64

Target Connection



Since Flasher Portable is compatible to J-Link it also supports the same target interfaces.
Currently the following target interfaces are supported:

  • JTAG
  • SWD
  • FINE
  • SPD

For more information about the target interfaces please refer to J-Link - Interface description.

Standard 20-pin connector pinout

 

 

Flasher Portable uses the standard J-Link 20-pin connector. There are various adapters available to fit all customer needs.

JTAG interface connector signals:

PinSignalTypeDescription
1VTrefInputThis is the target reference voltage. It is used to check if the target has power, to create the logic-level reference for the input comparators and to control the output logic levels to the target. It is normally fed from Vdd of the target board and must not have a series resistor.
2VsupplyNCThis pin is not connected in Flasher Portable. It is reserved for compatibility with other equipment. Connect to Vdd or leave open in target system.
3nTRSTOutputJTAG Reset (optional). Output from Flasher Portable to the Reset signal of the target JTAG port. Typically connected to nTRST of the target CPU. This pin is normally pulled HIGH on the target to avoid unintentional resets when there is no connection. Not mandatory for Flasher operation. Should not be shortened with RESET. In case of doubt, leave open/unconnected.
5TDIOutputJTAG data input of target CPU.
It is recommended that this pin is pulled to a defined state on the target board.
Typically connected to TDI on target CPU.
7TMSOutputJTAG mode set input of target CPU.
This pin should be pulled up on the target.
Typically connected to TMS on target CPU.
9TCKOutputJTAG clock signal to target CPU.
It is recommended that this pin is pulled to a defined state on the target board.
Typically connected to TCK on target CPU.
11RTCKInputReturn test clock signal from the target.
Some targets must synchronize the JTAG inputs to internal clocks. To assist in meeting this requirement, you can use a returned, and retimed, TCK to dynamically control the TCK rate. Flasher Portable supports adaptive clocking, which waits for TCK changes to be echoed correctly before making further changes. Connect to RTCK if available, otherwise to GND.
13TDOInputJTAG data output from target CPU.
Typically connected to TDO on target CPU.
15RESETI/OTarget CPU reset signal. Typically connected to the RESET pin of the target CPU, which is typically called "nRST", "nRESET" or "RESET".
17DBGRQNCThis pin is not connected in Flasher Portable.
It is reserved for compatibility with other equipment to be used as a debug request signal to the target system.
Typically connected to DBGRQ if available, otherwise left open.
195V-Target supplyOutputThis pin can be used to supply power to the target hardware. Supply voltage is 5V, max. current is 300mA. If not needed, leave open.

Notes:
All pins marked NC are not connected inside Flasher Portable. Any signal can be applied here; Flasher Portable will simply ignore such a signal.
Pins 4, 6, 8, 10, 12, 14, 16, 18, 20 are GND pins connected to GND in Flasher Portable. They should also be connected to GND in the target system.
Power can be controlled via the J-Link commander. The following commands are available to control power:
CommandExplanation
power onSwitch target power on
power offSwitch target power off
power on permSet target power supply default to "on"
power off permSet target power supply default to "off"
 

  • Flasher Portable
  • 20 Pin 0.1" Ribbon Cable
  • USB Cable
  • 3 piles AAA 
Fabricants
Recherche rapide
 
Utilisez des mots-clés pour trouver le produit que vous recherchez.
Recherche avancée
Langues
English
Pour Nous Contacter: O1 3O 50 O9 36
Information fabricant
Segger
Page d'accueil de Segger
Autres produits
Informations Paiement
Envoi rapide par UPSPaiement Sécurisé <br/>3D Secure
VISAMasterCard

Paiement Sécurisé
3D Secure

Boutique Mini PC

Boutique Mini PC
Affichage,
Controle Industriel,
Transports