Flasher PRO
[5.17.01]

798€ HT

[EN STOCK]
Programmeur de Flash  PRO pour ARM7/9/11, Cortex, RX et PowerPC

Flashage sur différents types de micros
Flasher PRO
CommanderAvis des clients

 
Programmeur de flash par JTAG/SWD autonome (une fois chargé, le Flasher peut etre actionné sans utiliser de PC)

-Support des ARM 7/9 ,Cortex-M3 , Renesas RX, PowerPC
-Interfaces Ethernet,USB,RS232
-Mémoire interne  128Mo
-Pas d'alimentation spéciale, alimenté par USB
-Compatible J-Link
-Vitesse de programmation 30k-1Mb/s selon cible
-Pilotage par commandes ASCII (sans utiliser de programme spécial)
-Protection “Authorized Flashing” possible

-Garantie 1 an, Support 2 ans
Le Flasher PRO de SEEGER est un outil de programmation pour les microcontroleurs avec mémoire flash embarquée ou externe et coeur ARM/Cortex, RX ou PowerPC . Le Flasher PRO est concu pour programmer les mémoires flash des cibles par PC avec le logiciel J-Flash ou en autonome. De plus le Flasher PRO possède toutes les fonctionnalités d'une sonde de debug J-Link. Le Flasher ARM se connecter par USB, Ethernet ou via un port RS232 sur un PC, fonctionnant sous Microsoft Windows 2000, Windows XP, Windows 2003, Windows Vista, Windows 7, Windows 8 ou Windows 8 et possède un connecteur JTAG 20-broches, compatible avec le connecteur standard JTAG 20-broches défini par le connecteur ARM

Specifications

 

 

Power SupplyUSB powered, 100mA for Flasher PRO. 500 mA if target is powered by Flasher PRO
USB Host InterfaceUSB 2.0
RS232 Host InterfaceRS232 9-pin
Target InterfaceJTAG 20-pin (14-pin adapter available)
Serial Transfer Rate between Flasher PRO and TargetMax. target interface (JTAG, ...) speed: 15MHz
Supported Target Voltage1.8 - 5V
Current drawn from target voltage sense pin (VTRef)< 25µA
Target supply voltage5V
Target supply currentMax. 400mA
Operating Temperature+ 5 °C ... + 60 °C
Storage Temperature- 20 °C ... + 65 °C
Relative Humidity (non-condensing)< 90% rH
Size (without cables)121mm x 66mmx 30mm
Weight (without cables)120g
Supported OSMicrosoft Windows 2000
Microsoft Windows XP
Microsoft Windows XP x64
Microsoft Windows 2003
Microsoft Windows 2003 x64
Microsoft Windows Vista
Microsoft Windows Vista x64
Microsoft Windows 7
Microsoft Windows 7 x64
Microsoft Windows 8
Microsoft Windows 8 x64
Microsoft Windows 10
Microsoft Windows 10 x64
 

Target interfaces

 

 

Since Flasher PRO is compatible to J-Link it also supports the same target interfaces. Currently the following target interfaces are supported:
  • JTAG
  • SWD

For more information about the target interfaces please refer to J-Link - Interface description.
Please note that Flasher PRO currently does not support SWO.
 

Performance of MCUs with internal flash memory

 

 

The following table lists program and erase performance values for different controllers.
MicrocontrollerSize [KB]Program time* [sec]
Analog Devices622.286
Atmel AT91SAM7S64643.488
Atmel AT91SAM7S2562567.709
NXP LPC17685128.559
NXP LPC21061201.204
NXP LPC21292482.916
NXP LPC21385005.488
NXP LPC21485005.632
NXP LPC2294204815.976
NXP LPC24785045.419
ST STM32F103ZE51218.763
ST STR7112725.476
ST STR91254412.907
TI TMS470R1B1M10248.147
TI MSP432P4012560.50

* Pure programming time. Total time including erase + verify heavily depends on factors like: Sector size, erase speed of flash, if flash was empty (no erase necessary) or already programmed (erase necessary)

JTAG Speed

 

 

There are basically three types of speed settings:

  • Fixed JTAG speed
  • Automatic JTAG speed
  • Adaptive clocking

Fixed JTAG speed
The target is clocked at a fixed clock speed. The maximum JTAG speed the target can handle depends on the target itself. In general ARM cores without JTAG synchronization logic (such as ARM7-TDMI) can handle JTAG speeds up to the CPU speed, ARM cores with JTAG synchronization logic (such as ARM7-TDMI-S, ARM946E-S, ARM966EJ-S) can handle JTAG speeds up to 1/6 of the CPU speed. JTAG speeds of more than 10 MHz are not recommended.

Automatic JTAG speed
Selects the maximum JTAG speed handled by the TAP controller.

NOTE:
On ARM cores without synchronization logic, this may not work reliably, since the CPU core may be clocked slower than the maximum JTAG speed.

Adaptive clocking
If the target provides the RTCK signal, select the adaptive clocking function to synchronize the clock to the processor clock outside the core. This ensures there are no synchronization problems over the JTAG interface.

NOTE:
If you use the adaptive clocking feature, transmission delays, gate delays, and synchronization requirements result in a lower maximum clock frequency than with non-adaptive clocking. Do not use adaptive clocking unless it is required by the hardware design.

 

Specifications

 

 

Power SupplyUSB powered, 100mA for Flasher PRO. 500 mA if target is powered by Flasher PRO
USB Host InterfaceUSB 2.0
RS232 Host InterfaceRS232 9-pin
Target InterfaceJTAG 20-pin (14-pin adapter available)
Serial Transfer Rate between Flasher PRO and TargetMax. target interface (JTAG, ...) speed: 15MHz
Supported Target Voltage1.8 - 5V
Current drawn from target voltage sense pin (VTRef)< 25µA
Target supply voltage5V
Target supply currentMax. 400mA
Operating Temperature+ 5 °C ... + 60 °C
Storage Temperature- 20 °C ... + 65 °C
Relative Humidity (non-condensing)< 90% rH
Size (without cables)121mm x 66mmx 30mm
Weight (without cables)120g
Supported OSMicrosoft Windows 2000
Microsoft Windows XP
Microsoft Windows XP x64
Microsoft Windows 2003
Microsoft Windows 2003 x64
Microsoft Windows Vista
Microsoft Windows Vista x64
Microsoft Windows 7
Microsoft Windows 7 x64
Microsoft Windows 8
Microsoft Windows 8 x64
Microsoft Windows 10
Microsoft Windows 10 x64
 

Target interfaces

 

 

Since Flasher PRO is compatible to J-Link it also supports the same target interfaces. Currently the following target interfaces are supported:
  • JTAG
  • SWD

For more information about the target interfaces please refer to J-Link - Interface description.
Please note that Flasher PRO currently does not support SWO.
 

Performance of MCUs with internal flash memory

 

 

The following table lists program and erase performance values for different controllers.
MicrocontrollerSize [KB]Program time* [sec]
Analog Devices622.286
Atmel AT91SAM7S64643.488
Atmel AT91SAM7S2562567.709
NXP LPC17685128.559
NXP LPC21061201.204
NXP LPC21292482.916
NXP LPC21385005.488
NXP LPC21485005.632
NXP LPC2294204815.976
NXP LPC24785045.419
ST STM32F103ZE51218.763
ST STR7112725.476
ST STR91254412.907
TI TMS470R1B1M10248.147
TI MSP432P4012560.50

* Pure programming time. Total time including erase + verify heavily depends on factors like: Sector size, erase speed of flash, if flash was empty (no erase necessary) or already programmed (erase necessary)

JTAG Speed

 

 

There are basically three types of speed settings:

  • Fixed JTAG speed
  • Automatic JTAG speed
  • Adaptive clocking

Fixed JTAG speed
The target is clocked at a fixed clock speed. The maximum JTAG speed the target can handle depends on the target itself. In general ARM cores without JTAG synchronization logic (such as ARM7-TDMI) can handle JTAG speeds up to the CPU speed, ARM cores with JTAG synchronization logic (such as ARM7-TDMI-S, ARM946E-S, ARM966EJ-S) can handle JTAG speeds up to 1/6 of the CPU speed. JTAG speeds of more than 10 MHz are not recommended.

Automatic JTAG speed
Selects the maximum JTAG speed handled by the TAP controller.

NOTE:
On ARM cores without synchronization logic, this may not work reliably, since the CPU core may be clocked slower than the maximum JTAG speed.

Adaptive clocking
If the target provides the RTCK signal, select the adaptive clocking function to synchronize the clock to the processor clock outside the core. This ensures there are no synchronization problems over the JTAG interface.

NOTE:
If you use the adaptive clocking feature, transmission delays, gate delays, and synchronization requirements result in a lower maximum clock frequency than with non-adaptive clocking. Do not use adaptive clocking unless it is required by the hardware design.

 
  • Flasher PRO
  • 20 Pin 0.1" Ribbon Cable
  • Ethernet Cable
  • USB Cable
  • USB Power Supply
  • RS232 Cable (1:1)

Options :

Adapter Flasher ARM









Isolateur Flasher ARM





798€ HT

 
Fabricants
Recherche rapide
 
Utilisez des mots-clés pour trouver le produit que vous recherchez.
Recherche avancée
Langues
English
Pour Nous Contacter: O1 3O 50 O9 36
Information fabricant
Segger
Page d'accueil de Segger
Autres produits
Informations Paiement
Envoi rapide par UPSPaiement Sécurisé <br/>3D Secure
VISAMasterCard

Paiement Sécurisé
3D Secure

Boutique Mini PC

Boutique Mini PC
Affichage,
Controle Industriel,
Transports